Connect 2agent Consumers

Heat Magnets

Not enough good quality connection cables, the emergence of additional resistance in the joints, the presence of impurities in the water, especially iron compounds, greatly increasing the error readings. Topics Still, one can say that the electromagnetic heat meters have sufficient stability and metrology can be applied successfully, as in the single-and dual-in dimensions. Ultrasonic heat meters operate on the principle change the time of the ultrasonic signal from the source to the receiver signal, which depends on the rate of flow. There are many modifications of ultrasonic heat (Time and frequency, correlation, Doppler), but the basic principle of any one of them is similar to the following: on the tube next to each other established by the ultrasonic transmitter and receiver signal. The transmitter emits a signal through the fluid flow, and the receiver after a while it gets. Delay time between the moment of its emission and reception is directly proportional to the velocity of fluid flow in a pipe: it measured and its value is calculated fluid flow in the pipeline. Ultrasonic heat meters work well on mass flow of pure, homogeneous liquid in a clean pipe. However, the flow of liquids, with debris - scale, scale particles, sand, air bubbles and unsustainable consumption, they provide substantial evidence inaccuracies. Besides the standard functions to measure the flow of coolant, it temperature and pressure, calculate consumed or heat produced, ultrasonic heat meters can also have the function of regulating coolant supply via two independent channels. Mechanical heat meters (Vane, turbine, screw), the most simple instruments.

Ship Yard

Thereafter masking tape sealed the Bottom of the model (at the same time checked the resistance of the coating that mimics the copper plating. Secure model on a stand, stand, secured inside the frame. Filled with plaster those gaps, which remained after the initial stages. The putty has dried a bit and I learned model. Removed the masking tape. Since copper was okay - nothing is detached and moved away. Gave a day to harden the plaster. After this fine-tuning took up the waves and breakers and simulated jets from the hull of the model.

By max waves imposed a bit of plaster and leveled with a spatula in the direction of the wind. Got a tip waves, "blown out" and "crushed" by the wind. Then molded roller under knyavdigedom and diverging from the jet model .. Gave dry. In this work of plastering was completed.

All about everything needed about 25 kg of dry mixture. After drying, the plaster started to paint. For this used three shades (building acrylic dyes) - aquamarine, blue, white. The first layer - spread aquamarine and white, was very light. Painted the entire surface. As it turned out (no matter how the first time I drew Sea), the right thing. This, in my view, it is important - at first light, then dark. On the contrary do not get that effect, which in my view correctly the feeling of water. Brush. This, too, from my point of view is important. He remembered the videos and his impressions of seeing the sea surface, as the wave moves, especially when viewed from the water is clear. There are visible "jets" of water, they stretched the threads. And by the waves of water stretched jets. So here is the brush that the effect of "jets" provides. Dry dye. Further spread and aquamarine blue with a little white. Colored intervals between waves. Turned bright 'sunlit' tops of waves and the dark intervals between the waves. Dry dye. Then already leveled color on different sections, in accordance with their ideas of how to look like water. All completely dry. Went through the whole surface of the paint spray. Started to simulate the "sea foam". Shortly before work on the layout, I visited an exhibition of paintings from the stone. I remember the impression from the pictures on the marine theme and the winter landscape. Pen and snow was magical. So I decided to try proimitirovat something similar. Took most common mineral that is found in stores - table salt, extra. Promazyvayut tops of waves, the tops of jets, some points between the waves with white glue, then these areas would fall asleep with salt. Let dry. Brush cleaned debris. Then using a small brush dipped in water, adjust the shape and intensity of the "foam". Additionally manifested effect of salt. When dissolved in water and subsequent crystallization, it became more loose and gave small stains. This, in my view, quite successfully impersonate a foam and air bubbles in the water. After the final drying of the salt water and divorces again walked across the surface of the varnish aerosol. In this work of creating "water surface" had been completed. Currently work is continuing on the model. The model is now here in this state - completed installation of the upper deck guns. Photo essay on the creation of this and other models you can look online workshop Ship Yard on the table, and Kharkiv.

House Workshop

Workshop - it's like a great tool. Problem. The most important thing to understand - you do not know what you do and what you have to deal with in his studio. Whether to cut, or weld; either watch repair, then Does the car. Definitely you will be there to keep a set of tools and anything else. So do shop universal, and more - as much as possible.

Blessing is to have a closing observation well, and even more blessing - if an observation well will be part of the basement beneath the entire area of the shop. There great zalyazhet old furniture, bags of potatoes and cement (canister with mysterious stuff, which still can not think of what to do - But sorry to pour or dangerous). You'll be something there to produce - and will need the area called 'the finished product warehouse. " Frame any color - should be put, and that would not be dusty. Or boxes (for seedlings) crap.

So let it be the place. Bench, a desk - the center of the studio. From it all begins, without a workshop does not happen. So - certainly Pick up a desk-bench. It does not matter - with drawers or without metal or wood - the main thing that would be strong and stable. That is a very strong and very stable. Physically, that would be impossible were it to break. Dining table will not work, kitchen - so yourself. On it you fix a vise, it will be the anvil, the grindstone - you name it.

Pasta Cleaning

During the operation, any samovar is losing its appearance. To samovar not lost his new look for him to care. You can give your samovar to polish experienced polisher to remove the old nickel, and then polished samovar. It is theoretically possible, and at home to polish my samovar. Remove the old nickel in several ways: in acid, electrochemical (swap the anode and cathode, ie, using the inverse polarity) and mechanical - a lengthy process of polishing. But it is polished samovar can only be mechanically polishing machines.

But apart from polishing to look at the samovar and at home. Electric samovar special care is not required. Electric samovar, as a rule, is at home indoors, and use it there, not exposing the aggressive factors of the environment. With him regularly enough to wash the dust and take a means of scaling and during use. With water galleries samovar is much more complicated. Flame samovar samovar he's coal, wood, heats the water due to combustion inside. From this it can be smoked and covered with resin and from cones to it need special care.

To solve this problem, there are special cleaning samovar. One of these tools - metal cleaners. It is suitable for cleaning of any products made from copper, brass and so on. Buy this product can be in the shops, on sale samovar, and in hardware stores. Second - Pasta goyim, is used to polish the samovar, but for cleaning the samovar, it is not suitable. Pasta Gentiles used to polish a samovar. For cleaning the samovar, it does not fit, can be used only after the metal-cleaners-like tools. Used metal cleaners, such tools are very simple. The soft rag put a little metal cleaners, and a circular motion rub the samovar. Samovar comes pretty quickly to its previous state. After that, to shine, you can grate the samovar paste the goyim. The problem with the brass polished samovar can also be solved at home. Yellow color makes the samovar brass. Brass tends to rust, red spots appear on the samovar. To deal with them fairly easily. Can use metal cleaners ilipasta Gentiles, but Gentiles paste is preferable. But, nevertheless, feel the need to remember that any samovar must be kept in a warm dry place, especially polished samovar, subject to 'bloom'. Observing all of these conditions during storage and use of a samovar, you will not have to deal with cleaning the samovar.

How To Get Closer To The Fish

1. Success awaits anglers only when he is able to quietly approach the fish. First of all, he should know that fish are capable to perceive at a distance. They have the authority, able to instantly respond to a shock wave. It operates separately from the view, that is, the fish can see the approach of the fisherman, not seeing it. 2.

Shock waves arise, always, with a careless walking on the beach or the bottom of the reservoir. If the angler wants to carefully approach the fish, it must step so as to avoid oscillations of the earth. Cause fluctuations of dense clay or rocky soil is not as easy as swampy soil, pebbles, gravel or podmyta coast. First and foremost, you should always pay attention to the ground, to look where to step and put his feet gently. This rule should be followed more strictly than closer to the fish.

3. When carelessly, hastily walking on the bottom of the pond too poluchayutsya shock wave. So go to a calm, measured movements. 4. When fishing from a boat also can scare the fish produced by shock waves. They arise in rocking the boat, spanking paddles immersed, bounce of the armature the bottom and blows the various items on the boat. 5. Just as you feel at a distance, the fish should not see you. When fishing from a boat your silhouette should be less desirable. Who rises in the boat when fishing lure at full length, and even at shop, seen from afar fish, overtaking trolling. She immediately stop the persecution and swims away. 6. The same applies to fishing from a float. If a fisherman sees a fish, and fish can also see him, if his silhouette towering over the water. In this case can hardly expect a strike. 7. On the course it is always possible to approach the fish against the current, ie, from behind. In standing water the likelihood that fish will notice the fisherman, much more, as they stand, and, therefore, see different directions. 8. In order not to be seen in fish on the shore, the angler should always try to be in front of or behind a tree, shrub, elevation of the coast, rock, wall or anything like that, hiding the body type, or better yet hand and rod. Located behind the fisherman's shelter is better than any, just prior to a fisherman. Even if the arms and the rod beyond the silhouette of the shelter, they can be seen in fish is not too sharp movements, like swinging in the wind branch. 9. Angler should always avoid sudden movements. If his movements are calm and slow, they are perceived as natural fish, and it is not evident from a distance. 10. Fish can notice the presence of a fisherman on the water falling on the shade. Therefore it is impossible to lower the sun is behind him. With a high sun shade low, low, it falls to the shore.

Hand Made Gifts

Close people want to give something special, co-workers surprise. We go to many hours of shopping trip in hopes of finding "a thing", and indeed there is much more easy, efficient and, importantly, less expensive way congratulate all. Exclusive things and souvenirs hand-made can do themselves, investing in gift warmly all Best wishes. Creating gift own hands begins with ideas. Good idea - is luck it opportunity materialize air lock celebrant. Find such opportunity can in your conversations with closest person or colleague in his "thoughts aloud". We rarely dreaming so was imperceptibly, Your task now - to see someone's dream.

The idea that to make a gift with their hands not to everyone's forces - no more than a myth, to realize the idea is most often much lighter than its "birth". Contrary to the adage, all hands are growing out of the same place, which means that everyone can do something truly talented. Uncertainty appears when you compare yourself with others. But the opportunity to implement an idea - a great set! The concept of "gift with their own hands" not limited to the theme of souvenirs, but where in fact its borders, it's up to you. And we try to give a line of thought.

Congratulations Congratulations are created with your hands and your thoughts. Of course, you can buy a postcard, where all you have to say, say it for you. But it's much better to stretch the imagination, and write something more than "wish you happiness in your personal life." A good solution to this problem will be deciphering the traditional wishes.

Oblic Villeroy Plumbing

As the classic series and Sentury Hommage Villeroy & Boch can be equipped with wooden seat and lid for toilet bowls, typical wooden cabinets under sinks with checkered fabric curtains, and a harmonious blend in the cozy bathroom country style. In addition, Besides the traditional snow-white color, you can choose a warm cream color pottery (the color of melted milk - pergamon). Truly a work of art is a series of plumbing Pure Stone Villeroy & Boch for fans of ethnic styles, or minimalism. Design of a series inspired by the shape and color of river stones: rounded and asymmetrical plumbing granite-gray just exudes a sense of natural harmony. Special attention is given a series of wooden plumbers New Look Dr.Jet, which has become a challenge for the world, undermining all representations about the plumbing, made of solid massive teak: washbasin Onda smoothly curved, free standing whirlpool shower cab Spira - curved round in a spiral, and a round bath Suprema - certainly become an altar in the bathrooms in the country style or ethnic. Dynamic, rapid series of plumbing Oblic Villeroy & Boch perfect for guests or small toilets in the "modern" styles thanks to its original futuristic design (decorative beveled toilet bowls, wash basins and urinaly bend and direct placement, as if in motion) allows efficient use of space small bathrooms, not constraining convenience. Series Architect Duravit partly echoes the same principle: toilets, sinks corner and direct attachment to the decorative urinal thickened walls, with an unusual solution water dispenser - as if they are inclined to side (in the form of a parallelogram).

Optimistic and cheerful series Joly Keramag: toilet bowls, wash basins and urinal - reminiscent of a round ball - Ergonomic thought out and well designed to maximize space in small bathrooms. For the youngest users bathrooms have a series of Kind / Baby Keramag: a specially designed comfortable and ergonomic series plumbing for children. Besides, what parent toilet for children too big to sink and they simply do not hold out, children are very important to have something of their own. They love their toy - a fantastic world, and such plumbing will be part of their game world, the adoption of hygienic procedures will be interesting for them. You can create a parental bathroom's corner with children's toilet and sink, or take your child's personal bathroom. Bathroom should be not only beautiful but also convenient. Large selection of plumbing different trends, styles and manufacturers in the plumbing shop Vodoparoff.ru shop window is constantly updated and new collections.

Internet Goods

Here's the second mass trend we have today and we'll talk. Many are able to evaluate the possibility of promoting their services through the Internet. But we are talking today about it and e-commerce sales of goods over the Internet. Type software, which allows a virtual sales, called the online store. Online stores apparently can be quite different, but they all have in common.

Here, perhaps, a few positions that combine all the services under the name of an online store: In any online store have the opportunity to register the buyer - it is a small electronic questionnaire, which aims to document the main customer data. Registration may, at the request of the shopkeeper, to be mandatory or optional. Normally when creating an online store, we recommend our customers an option when the user can assemble a basket of commodity, then during the ordering process is registered. Thus we increase the potential interest in buying it at this online store. As practice shows, the complex registration before purchase repels up to 20% of potential buyers of your online store, and collected a basket full of goods - it's the efforts that most buyers do not want to waste, so registration is much easier after filling the basket. The second point, which unites all the online stores, this basket - a software option that allows the buyer to make a consolidated order in your online store will automatically calculate the total cost of the order, read the terms of delivery or discounts that are possible in order for this amount. To increase sales effectiveness in creating an online store, we offer our clients a variety of information services. Formed by analyzing your customer baskets such services may draw his attention to other goods, goods with alternative specifications of the same commodity group, or simply inform the customer about discounts for this product.

The Site

The next thing to notice is the TIC and PR directory. But do not stop at just check the main page, be sure to find out which items from the page, which will be located your link. The fact is that search engines rank individual pages, and only then the average value for the entire site. So if the main page PR is, say, 5, and a page with your link 0, you will not get the expected weight gain his sayta.Nesmotrya that the TIC figures and PR, are important, you should not ignore the new directories with low or even zero rates. These resources are often increasing their weight in the index of search engines is very rapidly, and hence the weight of the links to your site will grow with them. Conclusion: do not dwell only on the numerical performance catalog, study quality. At what other points you should pay attention before idea to start the site catalogs? are primarily thematic site directories - they will not only significant external links on the site, but such a precious and targeted traffic. Note the URL where intend to place a link.

The shorter and clearer the page address, the server is friendlier to search engines. For example, the page URL: much faster will be indexed, rather than the page with the URL index.php? Ui = Reclrus & s = sites + catalogue. Further look at how long you have to get to the presentation of the site directory. The less clicks you make, the better.

Front Page Express

Do not get the results you want from your site? Have you noticed that the website of your competitor is better than yours? You may need to redesign the site and to introduce new colors, more content, better navigation. You really need to redesign your site at least once a year. Another word, a site redesign, what you need. The appearance of your site can make a breakthrough and bring you success. This is no joke. Do you have only a few seconds to make a first impression on the person and if the design is not good, you lose a potential customer.

Attention to detail and a good sense of design can go a long way. Contrary to what someone may have already saying you do not need a lot of jewelry and modules, to entertain visitors. Simple, well-designed site, usually a winning combination. Who wants to wait 5 minutes per page load? Do not we! Music, flashing graphics, moving text. Have you seen 'it' to competitors' sites, which could lead to the collapse of your browser or download the plugins only demand to view them. They will slow you down. Remember, just because that 14 year old kid from school can create a web page using a program Front Page Express, does not mean that it will be a success. It takes talent, skills and a lot of hard work to be able to create a successful Internet presence.

Experienced specialist to redesign the site to cope with your work. A quality website redesign is made up of many components, but is in first place udostvo (usability) for the visitors. When a person enters a long time can find a menu or slischkom small text to understand the menu, it is strongly razdrozhaet visitors and they can leave your site without any desire to return, which means no performance site and your business. Site redesign - your success.

Site Map

Navigation service can be seen on every Web server. It should provide easy access to service section ("sitemap", "send a message.") So, here are some key points that will help create high-quality navigation: First - is a handy navigation bar. What is it? This list of references, which is located at all pages. The second - using tools such as site map. Site Map - this tree is a logical site structure, it includes a list of all sections and pages.

Third - Provide access to information. Researchers say that if a visitor can not find the required two - three stages, it leaves the site. Fourth - repeat the main links, for example, at the bottom of each page. It is very easy to move through the site, allows quickly return to the main sections. Fifth, use the section headings and pages. Each section or page should have its own title. This allows the user to always know where it is and easy to understand where to move on. Qualitatively made navigation necessarily reflect the logic of user Web site and provide their needs.

All materials should be clearly structured. It is necessary that any people could easily navigate the information flow and easy finding him subsection and passed it. I think we have convinced you that even a very attractive and interesting site would not be useful and popular, in the absence of competent navigation. Navigation - this scheme. Diagram showing how to move from one section of the website to another. This is the most familiar and at the same time a complex element of the future development of the web resource. Navigation should be simple, comfortable and easy to understand. Unfortunately, these requirements and usually cause problems for many Web developers.

Administrative Offences

Help is issued for the acquisition of weapons will not do. Said medical certificate is presented as passing the skipper technical inspection of the vessel. According to the adopted changes in the rules of certification of skippers GIFT will not get certification for operators of small boats with motors 5 hp and less That is, owners of electric motors, and outboard engines with a capacity of less 5l.s. seemed to be enough to rub their hands. Now they do not need to spend money on a costly training and to obtain "rights." But do not rush to do so. Here is an excerpt from the changes - "the state inspection certifies the skippers and will issue a certificate of competence for self-propelled vessels of inland navigation tonnage less than 80 tons of the main engines of more than 3.68 and not more than 55 kilowatts or outboard engines power more than 3.68 kilowatts. " The key word here - attests. I would like to draw the attention of navigators that No other regulatory documents that prescribe a skipper's license for the right to control small boat regardless of the type and engine power is not changed.

Therefore, representatives of GIFT may require the presentation of the master's "rights" and, accordingly, to impose an administrative penalty for lack thereof, irrespective of the power installed on board the engine. And while there will be added appropriate changes to the Code of Administrative Offences of the Russian Federation and Terms of Use small boats on water bodies of the Russian Federation on water conflicts are possible. In addition, in the form and certificate of competence small boat motor power is not specified, and specifies only the type of vessel, skipper who has the right to control - motor boat, boat, jet ski or sail.

Stroller

When choosing a stroller should be the first thing to decide - how old the child she is adopted. More precisely, even important than age, but what if your baby can sit up. Or the child is so small that while it can only lie down. For newborn baby will only fit a buggy in which there is a horizontal position. Until the baby can not sit, sit-down wheelchair can not be used, even under the back enclosing baby pillows. This may harm your baby. So, up to 6 months - only recumbent wheelchair! Then the kid grows up and tries to sit down.

At this time, you will need wheelchair, which has a semi-lying (about 45 degrees) and sitting (almost 90 degrees) position back. Then the baby begins to walk. Now you need wheelchair, which can have both a sitting position and reclining - in case you get tired of walking crumb and decides to take a nap. It takes a little more time - and that's a dream to walk has become a rarity - the kid wants to stomp feet and play with other babies. At this time, already seated stroller. The main thing - to get to the walk! The main requirement for a wheelchair at this time - so the child could easily plant and remove it from the "transport". On average, parents use strollers only until the child reaches 2 years.

Then stroller or disappears completely out of use, or stays on long trips in case clinic or store. The child is growing very quickly, and rarely from parents using the entire two-year period a wheelchair. Most often it is two wheelchairs - one in which children carry to walk up to a year, and the second - in which the walk after year. "Why do I need two strollers?" - You ask - "After all, you can just buy one in which the will and the reclining and sitting, and the child removed easily when grow up! Wise producers certainly took into account all the needs of growing child! "Let's try to explain this phenomenon.

Strong Cheap Metal Doors

Due to the increasing volume of production, a joint stock company 'Metkon' opening event on the fall market price for the metal doors Series 'Economy +'. Currently you can buy excellent iron door, guaranteeing compliance with any and all examples of the quality and characteristics of housing professional scent design of only five thousand rubles! The doors of the company 'Metkon' undervalued - it is pure savings without damage to quality. This is - without profit trick. It is the right choice, which is worthy of all Muscovites. Conventional steel doors are ideal for both populated and for the productive sectors. Now the probable purchasers of the metal door is a rare opportunity to get acquainted with the production of closed joint stock company "Metkon" on our core potrale. Well-researched and easy interface allows users to to detail our proposed study door, exterior design process, form the base ukomplektatsii. You can also find many other useful links.

Our main products are - it's steel and iron doors of the six complete price variation of species, also manufacture metal grilles, railings, fences, gates and roofs of very strong steel from the well-known Russian producers. Firm for the supply of steel "METKON" everything else successfully develops activities such as sale of steel doors on the individual schemes: for any doorway, and taking into account all customer's preferences. It should be understood that a suitable iron doors for each otdelnogozakazchika can not be found. You must deliberately choose the model of the door to an acceptable figure for your money. Note that the fidelity of your purchase depends on the duration of the term Burglar resistance operation and the front door, which means the security of your personal integrity and acquired property. Powerful alloy, interesting design and installation of steel doors have earned positive feedback companies 'Metkon' among frequent shoppers.

We, in turn, always take into consideration the preferences of their customers. By the same firm for the sale of metal structures "METKON" can offer potential customers a great range of services delivery and installation in a doorway you purchased the iron door. And now the surprise - completely free of charge. Check out the professional installer to place is made at any time.

The Tongue

Tape Glazing - glazing, consisting of several individual window units, arranged in a horizontal direction and connected to each other. Velux window - a window installed in a roof construction at a given angle to the horizontal plane. Valve is usually fixed in two positions: either the upside - for convenience when washing windows, or slightly open, allowing Ventilate the area with strong wind, without fear that the window slammed shut. Mounting gap - the gap between the wall and the window opening frame window assembly. Is filled with insulating materials in the future subjected to finishing by running the slopes. Mosquito nets (protivomoskitka) - aluminum frame with a stretched grid on it, which prevents penetration of insects flying through the open windows. Set with special fasteners, if necessary, easily removed. Scissors - hardware element that is used in framuzhnyh and swing-out designs of the windows.

Provides fixation in the right half-open position of the window. Sash - sash structure consisting of bars and is designed for dividing a field glass to hardening or leaf decoration. Window opening - an opening in the wall for mounting one or several window units. Its design also involves the installation of window sills, mounting gaskets, and the unit slope and flow. The main lock (central drive) - an element of accessories designed to install the handle on the wing and drive the locking mechanisms. Mounting plate - an element of fittings, shut-off opposite the tongue and is mounted on the frame, Face plate or impost. Slope - an element of the window opening, which is framed windows inside and outside. Slopes close the seams between the window frames and openings.

The slopes are plastered and overhead - of plasterboard, plastic, wood. Low tide - an element of window design, designed to drain away rainwater. Parallel-sliding sash - sash that moves in a horizontal direction parallel to the plane of the frame, which covers an adjacent, often blind, shutters.

European Association

Laminate flooring (laminate or laminate) - this is the only leader in sales among a relatively new product in the field of floor coverings. Thanks to modern decor, a new surface structure, there immeasurable feeling of absolute naturalness and genuineness of sex. Due to the increasing volume of construction and relatively high prices to the floor and work on its installation and dedication of people age-old traditions use of wood in interior design, it was dictated in favor of laminate flooring. Many manufacturers of laminates, after analyzed the properties of ordinary wooden coverings have created a material that not only was to have better performance and durability, but became different relatively low cost. This material has very accurately imitate natural parquet floors, antique wooden board, tiling.

Also, laminate is suitable for processing different types of interiors with any traffic (shops, restaurants, offices, exhibition and sports halls, hallways, bedrooms, nurseries, etc.). Laminate floors are laid on an existing base of "floating" manner. This method of installation has made laminated covering the most convenient and practical for installation in historic buildings in Western Europe. Premium products - a whole philosophy, the philosophy of the people for whom these products are created, not just an expensive product. And not only the price here is the main criterion.

As well as on any other market, the production of such coatings are applied the most modern technology and modern design. To determine an accurate assessment of quality in 1999 were introduced by the European norms of laminate flooring, which were approved by the European Association of manufacturers of laminate flooring (EPLF), which already includes about 20 countries. Each type of flooring is being tested on 18 different tests are conducted in accordance with strict requirements of the Association, including checking for impact resistance, moisture resistance, sound insulation, abrasion resistance, ecological purity materials, etc. On the basis of tests carried out sex assigned certain class of wear-resistant coatings. The most popular classes in Russia today - a 32 and 33 class. Therefore, the higher class laminate, the longer its life.

Automatic Gates: Select Manufacturer

Just a few years ago, being in America or Western Europe, we wondered what to get to the garage and into the yard, not out of the car and not touching the hands of the gates, gates and even their pens out there - a common practice. Today in Russia automatic garage and gate opening up from the console, become just as affordable and common as foreign cars or plastic windows. Several varieties of garage doors, ranging from the most accessible sets the order of ten standard sizes, sold in network building hypermarkets, which are ready to assemble, to unique projects, made to order. However, when selecting the gate enough to determine their type and approximate cost. Important to understand the differences between manufacturers of these products, because you want to know what's behind the difference in price and find the best offer. Often our choice of affect long-term stereotypes that not only are not relevant, but also interfere with the right to choose what we really fit the functional requirements, aesthetic tastes and demands of our climate. In the minds of Many of us have a "Soviet-era" left bias of the absolute superiority of foreign over domestic. But times change and one of the latest trends in economic development lies in the fact that products of domestic companies that have established their production facilities with modern equipment and developing products specifically for the Russian conditions, not only not inferior in quality, but also significantly superior to foreign analogues on the basic consumer properties, so it becomes more desirable.

Fuji Heavy Industries

In Japan defeated the U.S. occupation authorities have applied to the Nakajima Aircraft antitrust and restrictive laws, the company was renamed Fuji Sangye Ltd., As well as Japan it was impossible at that time to have an army, company has started to motor boats, cars, buses and gasoline engines - had to put achievements and talents in these areas. Automobile production is itself was not yet; it can be regarded as the harbinger released in 1946, scooter Rabbit ('rabbit'), which is used to create the remaining since the war aviation spare parts. In 1950 Fuji Sangyo disintegrated into 12 independent events, of which over time has ceased to exist. But already in 1953, five of the most robust of the departments of the company once again came together and united in Fuji Heavy Industries. Later they were joined by six.

Corporation, Headquartered in Hiroshima, has started to manufacture jet aircraft, chainsaws, scooters and Rabbit diesel buses and gradually sought more and more success. In 1954 he created the prototype of a car - P-1 (Subaru 1500), for the first time in the Japanese automotive industry realized monocoque body structure. For all its excellent driving performance and comfort of the car has not gone into production because of financial difficulties associated with its production and sales. But later he played a significant role in the development of models Subaru 360 and Subaru 1000. In 1971, Subaru launches model Subaru Leone - the world's first all-wheel drive passenger car, which caused huge interest both among professionals and among ordinary consumers.

Concrete Construction Durability

To date, one from the list of especially popular types of materials, without a doubt, it becomes concrete. Compared with other building materials, building concrete can have a large number of truly significant advantages, most important of which is its affordable price. Almost without exception, engaged in building the firm uses its own concrete, which, besides cost, is also characterized by high reliability, and in addition has high performance. The present concrete is characterized by a large selection of consumer options. Thus, by the way, different specialized concrete, concrete solution for pouring concrete in the construction, besides various concrete blocks specifically designed for the specific implementation options. In the immediate depending on demand at any particular Structural case is involved certain brand of construction of the concrete. This provides an opportunity to diversify the costs of various levels of construction as well as a variety of concrete stamps are not like the main user-defined parameters.

Some types of concrete used to lay foundation. This type of concrete, characterized by much more reliable and immune to regular and serious military action, and in addition continuous action of the soil. Certain types of concrete structures are designed to form the walls, and - for decoration and other procedures. I mean, the concrete 100 has a real purpose, which provides opportunity for any type of work to choose the most suitable type of concrete. Such differentiation provides a practical opportunity to lead the construction of buildings more efficient and save money for that. Since, clearly, additional power of a brand building concrete lead to an increase in its value.

Latest advances allow to acquire concrete building with the most varied, and in fact quite a bit of time ago, is absolutely incredible performance. Here, for example, foam may be so insignificant weight that will not drown in water, while a similar building material has the highest thermal insulation properties. Building, whose facade is made of foam construction will not require an additional layer of insulation, in addition, it constantly comfortable and did not hear the noise. For each type of action it is possible to select the most adequate view of the construction of the concrete. In this version, built design is characterized by high quality factor and thus be able to stand for many years, delighting those who will reside in such building or carry out the responsibilities for its important consumer characteristics.

Airplanes

Here we will first of all that, but what should look like a model airplane? "Or, to be exact - as perceived 'small' aircraft of different people. For the most part the majority of consumers remain quite satisfied your purchase, quality execution order. But there are, of course, a kind of neodnaznachnye opinions, judgments, perceptions of the 'real' model aircraft. It is clear that connoisseurs and collectors of good versed in many areas and aspects, and that is called "in the subject, so know in advance that they want to buy, and that suggests to see. A reaction to 'amateurs' in some cases it is best expressed in the issues that they asked. For example: - And why do the wings of these 'things' (in the sense of flaps) are not moving, and the tail does not rotate? - Chassis is removed? - Aaaaaa, 'it's made of plastic - So it's a designer But seriously, the model airplane can be accomplished in a variety of ways. Typically, a model airplane manufactured in the so-called office version, ie without the details, but the exact scale, bright glossy paints and varnishes, and looks good with different distances, and successfully conveys the idea - it is beautiful to show how the aircraft type and airline, or printed custom labels and logos. Another (also considerable) group consists of scale models of aircraft exclusive nature.

Can be accurately copied design features of the aircraft, the pointing, detailed coloring, bear the following scale, aging, retractable landing gear, interior lighting and so on and so forth. All list is almost impossible, because it is quite a separate issue. Naturally, it is meticulously hand-work done by these masters. So what do we want to see in a model airplane? Very interesting question! There are not weak sense is to ask yourself this question.

Transportation Companies

In modern society, just can not do without the services of transportation companies engaged in cargo transportation and related services, because almost everyone have something to carry. Generally, delivery of cargo - it rather troublesome, but half the problem solved immediately, because a lot depends on proper packaging and labeling of goods. This not only removes most of the contradictions, but also helps to avoid penalties and claims by police officers and customs officials. Since there are three main groups of goods (transported in containers, without or with the protection of certain parts, or parts thereof), then they should pack accordingly. Tara - this is what is packaged load on the plant or factory. But often it is not enough, so use special packing materials, as well as all sorts of attachment or other means (if necessary), which facilitate loading and unloading. There are three types of packaging: the consumer, and additional traffic. The first type relates directly to product packaging for delivery to the consumer, the second - the various boxes and cases, which are intended to protect from atmospheric phenomena, as well as for larger shipments.

Transport packaging protects mainly from mechanical damage during shipping. This is different boxes - wooden, plastic, metal, cardboard, jars, barrels, drums, etc. But the burden of loss not only protects the packaging, but also the observance of all rules of work and storage conditions, as well as the choice of packaging and delivery, depending on its characteristics and features. So, all factors affecting the safety of the cargo, is divided into three main groups - mechanical, climatic and biological. In other words, it is necessary to protect the product from impact, shock, scratches, precipitation or climatic conditions and damage by insects or rodents.

But at the same time, packing should not take too much space, does not preclude the possibility of automatic loading, to avoid burdening labor of workers, as well as maintain marketable commodity and beautiful (and carefully!) look like.

Smart Cards

She invented and patented a Frenchman Roland Moreno.Tam same in France, even after 10 years, Bull developed and patented the first smart card with built-in microprocessor. Experts who have studied the history of the origin of plastic cards, consider that the beginning of financial transactions with payment by the bank loans was laid by John C. Biggins, an expert on consumer credit from National Bank of Flatbush in New York's Brooklyn. In 1946, Biggins developed a credit system called 'Charge-it'. The essence of the scheme was that the stores have taken from customers in payment of personal receipts, and then attributed them to the bank and the bank, in turn, paid them off buyers. This classic chain of calculations improved version is still used in the banking business.

Epoch plastic cards flourished cards began with the advent of the world famous card American Express. She was released on October 1, 1958, and Within a year the owners of these cards are more than 475 thousand people and more than 30 thousand organizations and businesses. This success is due to several reasons. First, the company acquired Universal Travel Card, which is serviced by the Association of American hotels. Secondly, American Express had a tremendous financial opportunities for credit and a huge international network, serving travelers checks of the company. In the 1950-60s began a fundamentally new stage in the development of card business. More than a hundred American banks began to use credit cards for conducting financial transactions. The largest and most influential banks are: Bank of America and Chase Manhattan Bank.

Production Of PET Packaging

Polyethylene terephthalate (PET) has enjoyed considerable success in the market of packing materials in Ukraine and abroad. At this time, pet is used in the manufacture of packaging for different types of chemical, food, perfumes. pet is used as a convenient and practical material for packaging of food products around the end of 1970. Especially popular, he began to use in 1980, and in 1995-1999. production of pet containers for beverages rose more than twice. From 1990 to 2000, pet packaging has increased its market share in the packaging for beverages with a 9% to 35%. pet has become widely used and very popular material that is largely unable to replace glass and other plastics.

Along with his excellent physical properties, pet possesses another important advantage - an acceptable price. In pet many positive qualities. First of all - it's very easy material. The usual half-liter pet bottle weighs about 28 grams (a bottle of the same volume of glass can weigh about 350 grams). pet is completely transparent, making it ideal for bottling mineral waters and aerated water. To produce, which is in such containers are not exposed to sunlight, pet tint, for example, green or brown. It is also made to the appearance of products best meet the needs of the most demanding consumers.

The starting material for the manufacture of preforms are, from which after pre-heating of stretched and blown bottles. Preforms, in turn, are produced by of granular polyethylene terephthalate polymer. Color and transparency of future bottles are laid in the manufacture of preforms from the granules. Another advantage of PET-bottles - her strength, which is very important for storage and transportation. In this case, pet, as well as glass, fine (and completely) processed. For the packaging of pet containers are not required boxes, pack them in plastic wrap with a cardboard tray with or without him.

How to Purchase and Collect Artworks?

Anyone can purchase and collect art wisely. So, I told anyone. Do not need prior knowledge of the business of art, art collecting experience, or degrees in art history are required. All you need is love and appreciation of art, collected, and the desire for knowledge of simple techniques that will help you evaluate each work of art of all time by any artist of any nationality.

Although the following article contains specific recommendations and suggestions in relation to specific works of art, we must remember that art has no right or wrong way and right or wrong not to buy or collect art. Any person can choose what they feel like collecting art and buy what they feel like buying, where and when they want to buy it, for whatever reason they decide to buy, and money does not matter how you feel like spending it. As a result, these methods are not for everyone but are designed for people who like to spend your money wisely prefer to pay a fair price for quality art. If this happens, you will, what is about to read will help you become a better collector.

to be continued...